Meteoric iron used for keris's vs. for Indian weapons

BSMStar · 7th February 2005, 04:47 PM

Jens Nordlunde:

No doubt some nickel-iron type are not well suited for direct hammering. There are several factors to take into consideration... the crystal structure of the meteorite (from fine to coarse octahedrite, etc.), and metallurgy for example. The Gibeon Meteorite from Namibia, Africa is an example of a nickel-iron type that you can hammer directly without forging. Again, it goes back to the odds of the right type of meteorite falling in the right place at the right time.

Jens Nordlunde · 7th February 2005, 04:58 PM

Yes I have read that there are different types of meteoric iron, and also that the one with nickle is very difficult to use, but from the structure Master Daud must have been able to estimate how much 'normal' iron he had to mix it with. To have had this knowledge, he, or others, must have tried it several times to get that knowledge

Henk · 7th February 2005, 06:22 PM

Nechesh,

Of course the discussion should be academic and not based on rumours. Kraton empus did make keris for clients outside the kraton and used the surplus of the prambanan meteorite they received to make a court keris. I did read it in a dutch book: De Inlandsche Kunstnijverheid in Nederlandsch Indie (The Inland Artwork in Dutch Indie) by J.E. Jasper and MAS Pirngadie. This book was printed and published on behalve of the dutch government in The Hague in 1930.

I translate for you the passage in that book: "As pamormetal was and is used in the royal countries, the home of pamorforge art, metoric iron, that contains few nickle and is known as pamor parambanan. It is kept in the kraton of Soerakarta. Every time when the Soesoehoenan or other courtmembers want to forge a weapon, often a much too large piece of the meteor Iron was given to the empu, who had usually left a very large part of it.
That's why that it was possible to buy pieces of the pamor parambanan for the very high price of fl 2,50 to fl 10,00 for a rejal (30 gram)" That means in the currency of today the very high price of 1 euro to 4,50 euro for 30 gram.

About the use and being well known of the meteoric iron you misunderstood me. Using meteoric iron outside Indonesia for pamorforging is not well known.
Jens wrote that in India two swords, a dagger and a knife was made from the iron of a meteor. What I ment to say is that the use of the parambanan meteor for pamor weapons is well known (at least here in Holland) and that "a weapon made from the meteor was considered as the true holy weapon with pamor parambanan or pamor toenggal" (I quoted the book) Pamor forging was also done with other metals. The same book mention "the import of nickle bars, the pure Krupp nickle from the factory of A. Krupp from Berndorf, Germany. When this was used the pamordrawing came up very clear and shiny. Much more then when the real pamor iron of Parambanan was used."

BSMStar · 8th February 2005, 02:31 AM

Prambanan meteorite is on the Finest (crystal structure) Octahedrite, around 5% nickel...
http://internt.nhm.ac.uk/cgi-bin/ear...y=P2270&index=

Also you have
Hexahedrites - low nickel bearing (up to 6%)
Octahedrites - medium nickel bearing (5 to 17%, mostly on the lower end) and classified from fine to coarse (in crystal structure) believe to be caused by the speed of cooling.
Ataxites - high nickel bearing (16% plus) note: they show no internal crystal structure.
http://www.alaska.net/~meteor/type.htm

BSMStar · 8th February 2005, 01:19 PM

Since the Prambanan meteorite wasn't introduced untill the 1700's... can some tell me how far back the nickel-iron parmor goes back? What was the early history of the metallurgy? Was it just Malelo before that?

Jens Nordlunde · 8th February 2005, 01:23 PM

Hi BSMStar,

Thank you for your answer. It is very interesting what you write about the different types of meteors, and the concentration of the different metals. I find it most interesting, that iron, even with a very small concentration of some other metal, can act very different when forged, and sometimes make it almost impossible to forge, if it is not treated in a very special way. When they, started to work with wootz steel and meteoric iron, it must have taken them a considered amount of time, until they had learned how to treat the metal so they could form it.
Sorry I can't help you with your new question.

Jens

fearn · 8th February 2005, 02:56 PM

I'm trying to remember where I read this: it was one of the contemporary knife catalogs, and the name escapes me at the moment (argh! I'll edit it in when I remember it!)

This is a sideline to the "meteoric iron" thread, but it is about the high nickel iron used to create pamor. Apparently, the volcanoes on Java cough out nodules of high-nickel iron, and that is what is (was) used for most keris blades, presumably along with low-nickel iron from other sources.

Apparently, westerners used to think that high-nickel iron only came from meteorites, and so among westerners, the story was that the pamor iron all came from meteoric iron.

This doesn't contradict the idea that some keris and other blades were made from meteorites. It simply says that most pamor blades have a strictly terrestrial origin, and Indonesia isn't a magnet for meteoric bombardment.

F

8th February 2005, 02:31 AM	#4
BSMStar Member Join Date: Jan 2005 Location: Kansas City, MO USA Posts: 312	Some more boring information Prambanan meteorite is on the Finest (crystal structure) Octahedrite, around 5% nickel... http://internt.nhm.ac.uk/cgi-bin/ear...y=P2270&index= Also you have Hexahedrites - low nickel bearing (up to 6%) Octahedrites - medium nickel bearing (5 to 17%, mostly on the lower end) and classified from fine to coarse (in crystal structure) believe to be caused by the speed of cooling. Ataxites - high nickel bearing (16% plus) note: they show no internal crystal structure. http://www.alaska.net/~meteor/type.htm

8th February 2005, 01:19 PM	#5
BSMStar Member Join Date: Jan 2005 Location: Kansas City, MO USA Posts: 312	When did Nickel first get introduced? Since the Prambanan meteorite wasn't introduced untill the 1700's... can some tell me how far back the nickel-iron parmor goes back? What was the early history of the metallurgy? Was it just Malelo before that?

7th February 2005, 04:47 PM	#1
BSMStar Member Join Date: Jan 2005 Location: Kansas City, MO USA Posts: 312	Jens Nordlunde: No doubt some nickel-iron type are not well suited for direct hammering. There are several factors to take into consideration... the crystal structure of the meteorite (from fine to coarse octahedrite, etc.), and metallurgy for example. The Gibeon Meteorite from Namibia, Africa is an example of a nickel-iron type that you can hammer directly without forging. Again, it goes back to the odds of the right type of meteorite falling in the right place at the right time.

7th February 2005, 04:58 PM	#2
Jens Nordlunde Member Join Date: Dec 2004 Location: Europe Posts: 2,718	Yes I have read that there are different types of meteoric iron, and also that the one with nickle is very difficult to use, but from the structure Master Daud must have been able to estimate how much 'normal' iron he had to mix it with. To have had this knowledge, he, or others, must have tried it several times to get that knowledge

7th February 2005, 06:22 PM	#3
Henk Member Join Date: Dec 2004 Location: The Netherlands Posts: 1,209	Nechesh, Of course the discussion should be academic and not based on rumours. Kraton empus did make keris for clients outside the kraton and used the surplus of the prambanan meteorite they received to make a court keris. I did read it in a dutch book: De Inlandsche Kunstnijverheid in Nederlandsch Indie (The Inland Artwork in Dutch Indie) by J.E. Jasper and MAS Pirngadie. This book was printed and published on behalve of the dutch government in The Hague in 1930. I translate for you the passage in that book: "As pamormetal was and is used in the royal countries, the home of pamorforge art, metoric iron, that contains few nickle and is known as pamor parambanan. It is kept in the kraton of Soerakarta. Every time when the Soesoehoenan or other courtmembers want to forge a weapon, often a much too large piece of the meteor Iron was given to the empu, who had usually left a very large part of it. That's why that it was possible to buy pieces of the pamor parambanan for the very high price of fl 2,50 to fl 10,00 for a rejal (30 gram)" That means in the currency of today the very high price of 1 euro to 4,50 euro for 30 gram. About the use and being well known of the meteoric iron you misunderstood me. Using meteoric iron outside Indonesia for pamorforging is not well known. Jens wrote that in India two swords, a dagger and a knife was made from the iron of a meteor. What I ment to say is that the use of the parambanan meteor for pamor weapons is well known (at least here in Holland) and that "a weapon made from the meteor was considered as the true holy weapon with pamor parambanan or pamor toenggal" (I quoted the book) Pamor forging was also done with other metals. The same book mention "the import of nickle bars, the pure Krupp nickle from the factory of A. Krupp from Berndorf, Germany. When this was used the pamordrawing came up very clear and shiny. Much more then when the real pamor iron of Parambanan was used."

8th February 2005, 01:23 PM	#6
Jens Nordlunde Member Join Date: Dec 2004 Location: Europe Posts: 2,718	Hi BSMStar, Thank you for your answer. It is very interesting what you write about the different types of meteors, and the concentration of the different metals. I find it most interesting, that iron, even with a very small concentration of some other metal, can act very different when forged, and sometimes make it almost impossible to forge, if it is not treated in a very special way. When they, started to work with wootz steel and meteoric iron, it must have taken them a considered amount of time, until they had learned how to treat the metal so they could form it. Sorry I can't help you with your new question. Jens

8th February 2005, 02:56 PM	#7
fearn Member Join Date: Dec 2004 Posts: 1,247	I'm trying to remember where I read this: it was one of the contemporary knife catalogs, and the name escapes me at the moment (argh! I'll edit it in when I remember it!) This is a sideline to the "meteoric iron" thread, but it is about the high nickel iron used to create pamor. Apparently, the volcanoes on Java cough out nodules of high-nickel iron, and that is what is (was) used for most keris blades, presumably along with low-nickel iron from other sources. Apparently, westerners used to think that high-nickel iron only came from meteorites, and so among westerners, the story was that the pamor iron all came from meteoric iron. This doesn't contradict the idea that some keris and other blades were made from meteorites. It simply says that most pamor blades have a strictly terrestrial origin, and Indonesia isn't a magnet for meteoric bombardment. F