VOC hanger advice

Jim McDougall · 15th November 2021, 12:23 AM

My personal opinion, as everyone here knows, is do not overclean, simply stabilize with something light like WD40 which will clean and show the wonderful patina.
As a historian, this is well earned over time and I feel it should remain. a weapon garishly cleaned into shiny awfulness to me is bad.

The grip is indeed not very good, but it is something, otherwise this would simply be a 'relic'.

As many of these as were in service, its amazing how hard they are to find. Always tried to find anything with VOC markings but never did.
These blades were produced in either Solingen or German shops in Netherlands, I forget the names of the cities. They were not issued, as VOC was private company so were sold to the individuals, as I have understood.

Rick · 15th November 2021, 02:50 AM

The stampings seem so crisp compared to the surface condition...
Agree w/Jim, leave it as it is.

cornelistromp · 15th November 2021, 08:49 AM

I would only treat it with crystalline wax, if you remove the patina it doesn't get any better. I would recommend to remove the wooden grip, this is a recent addition of the wrong model, it looks weird.

it should have a thin spiral grip on it. fe see attached example of a 1790 VOC Rotterdam cutlass and for others please see the thread:

http://www.vikingsword.com/vb/showthread.php?t=22313

best,

cel7 · 15th November 2021, 11:07 AM

Thank you all for the advice! I'll just leave it as it is. I will also leave the grip alone for now.

kai · 16th November 2021, 10:05 PM

I'm with Rick - compared to the corroded surfaces, the stamping seems exceptionally crisp. This may suggest a later (though also apparently not recent) addition.

If it's done later, it's a pretty good attempt. It does look more like a VOO (rather than VOC) though! Since these stamps were never standardized, maybe the C was just missing from the tool set and they had to use the O twice...

Regards,
Kai

mariusgmioc · 17th November 2021, 07:19 AM

The corrosion is quite deep but uniform and consistent with its age.
The stamp is crisp but it is also corroded consistent with the rest of the blade so I am pretty sure it is original and not a later addition. Also the marking shape and style are correct confirming they are the original.

I am not very knowledgeable in tackling this type of corrosion but I would only clean it with bronze brushes & steel wool and WD40 to remove the active rust.

Peter Andeweg · 17th November 2021, 08:43 AM

Agreed with all mentioned above, a nice blade but too deeply corroded to have it polished, the same for the guard. I think that some handy fellow had made this new hilt, but it sure does not add any value nor aesthetic pleasure.
The shell guard cutlasses or hangers are very scarce, I often encounter VOC marked blades with tribal or European military hilts, but rarely with the clam shell guard.

A good find!

15th November 2021, 08:49 AM	#3
cornelistromp Member Join Date: Mar 2009 Posts: 1,060	I would only treat it with crystalline wax, if you remove the patina it doesn't get any better. I would recommend to remove the wooden grip, this is a recent addition of the wrong model, it looks weird. it should have a thin spiral grip on it. fe see attached example of a 1790 VOC Rotterdam cutlass and for others please see the thread: http://www.vikingsword.com/vb/showthread.php?t=22313 best, Attached Images Last edited by cornelistromp; 15th November 2021 at 08:59 AM.

17th November 2021, 07:19 AM	#6
mariusgmioc Member Join Date: Sep 2014 Location: Austria Posts: 1,911	The corrosion is quite deep but uniform and consistent with its age. The stamp is crisp but it is also corroded consistent with the rest of the blade so I am pretty sure it is original and not a later addition. Also the marking shape and style are correct confirming they are the original. I am not very knowledgeable in tackling this type of corrosion but I would only clean it with bronze brushes & steel wool and WD40 to remove the active rust. Last edited by mariusgmioc; 17th November 2021 at 08:28 AM.

15th November 2021, 12:23 AM	#1
Jim McDougall Arms Historian Join Date: Dec 2004 Location: Route 66 Posts: 10,289	My personal opinion, as everyone here knows, is do not overclean, simply stabilize with something light like WD40 which will clean and show the wonderful patina. As a historian, this is well earned over time and I feel it should remain. a weapon garishly cleaned into shiny awfulness to me is bad. The grip is indeed not very good, but it is something, otherwise this would simply be a 'relic'. As many of these as were in service, its amazing how hard they are to find. Always tried to find anything with VOC markings but never did. These blades were produced in either Solingen or German shops in Netherlands, I forget the names of the cities. They were not issued, as VOC was private company so were sold to the individuals, as I have understood.

15th November 2021, 02:50 AM	#2
Rick Vikingsword Staff Join Date: Nov 2004 Posts: 6,339	The stampings seem so crisp compared to the surface condition... Agree w/Jim, leave it as it is.

15th November 2021, 11:07 AM	#4
cel7 Member Join Date: Apr 2015 Posts: 157	Thank you all for the advice! I'll just leave it as it is. I will also leave the grip alone for now.

16th November 2021, 10:05 PM	#5
kai Member Join Date: Apr 2005 Posts: 3,255	I'm with Rick - compared to the corroded surfaces, the stamping seems exceptionally crisp. This may suggest a later (though also apparently not recent) addition. If it's done later, it's a pretty good attempt. It does look more like a VOO (rather than VOC) though! Since these stamps were never standardized, maybe the C was just missing from the tool set and they had to use the O twice... Regards, Kai

17th November 2021, 08:43 AM	#7
Peter Andeweg Member Join Date: Feb 2020 Location: Vlissingen, Netherlands Posts: 71	Agreed with all mentioned above, a nice blade but too deeply corroded to have it polished, the same for the guard. I think that some handy fellow had made this new hilt, but it sure does not add any value nor aesthetic pleasure. The shell guard cutlasses or hangers are very scarce, I often encounter VOC marked blades with tribal or European military hilts, but rarely with the clam shell guard. A good find!