PORTION OF A CROSSBOW for ID

[Pukka Bundook]

Dear Corrado,

I have looked at the pictures, both the ones you kindly posted and also in Sir RPG's book.
Looking at the first pictures again, I think I have it. (but maybe not!)

You will note in Sir RPG's book, that the grooved area where the bolt lies, Crossbows can be made in various shapes, some convex and some concave along their length. I see in the first pictures posted, that there is a slight groove at the rear, and a deeper groove towards the front of the stock where the bolt lies. This arrangement is to be seen on page 70.

Cerjak,

A question if I may;
If you lay a straight -edge in the "bolt groove", does it touch at both ends and miss the metal bridge part of the bow?
In other words, is the grooved area slightly concave or dished from end to end??

Edited to add, after Another look;

Is the bow seated as deep as it will go into the stock??
I ask, as the 'wing nut" on the underside is only half threaded onto the bolt, and it looks to me like the bow could be tightened down into the stock more, causing the bridge area to become flush with the surface where the bolt lies.

Corrado,
Thank you for getting me to look at this closer, it is a very interesting piece!

[Cerjak]

Originally Posted by Pukka Bundook

Dear Corrado,

I have looked at the pictures, both the ones you kindly posted and also in Sir RPG's book.
Looking at the first pictures again, I think I have it. (but maybe not!)

You will note in Sir RPG's book, that the grooved area where the bolt lies, Crossbows can be made in various shapes, some convex and some concave along their length. I see in the first pictures posted, that there is a slight groove at the rear, and a deeper groove towards the front of the stock where the bolt lies. This arrangement is to be seen on page 70.

Cerjak,

A question if I may;
If you lay a straight -edge in the "bolt groove", does it touch at both ends and miss the metal bridge part of the bow?
In other words, is the grooved area slightly concave or dished from end to end??

Edited to add, after Another look;

Is the bow seated as deep as it will go into the stock??
I ask, as the 'wing nut" on the underside is only half threaded onto the bolt, and it looks to me like the bow could be tightened down into the stock more, causing the bridge area to become flush with the surface where the bolt lies.

Corrado,
Thank you for getting me to look at this closer, it is a very interesting piece!

Dear Richard
Yes the bow could be more into the stock
May this pictures will help you.

Best
Cerjak

[Pukka Bundook]

Dear Carjak,

Thank you for the additional photos.
I am now sure this crossbow was made for conventional bolts.

The actual bow is beautifully made, a real work of art!
I will keep looking, as I have not seen one exactly the same.
Do you have an idea where it could have originated?
To me it looks Germanic, but that is maybe because many were!

It is a great piece. Congratulations on finding it!

Richard.

[Cerjak]

Originally Posted by Pukka Bundook

Dear Carjak,

Thank you for the additional photos.
I am now sure this crossbow was made for conventional bolts.

The actual bow is beautifully made, a real work of art!
I will keep looking, as I have not seen one exactly the same.
Do you have an idea where it could have originated?
To me it looks Germanic, but that is maybe because many were!

It is a great piece. Congratulations on finding it!

Richard.

Hi Richard,
Thank you for your comment.

It had been sold as a portion of 16 th century Spanish crossbow.
Best

Cerjak

[Pukka Bundook]

I think 16th century sounds right Cerjak, but am totally ignorant of Spanish crossbows I am afraid!

If I find one like yours on line or in a book, I will post a picture.
Thank you again for showing it.

Kind regards,
Richard.