Mongolian? Knife/sword

Shakethetrees · 9th September 2014, 05:07 AM

Polished and etched!

I had a little time on my hands today and cleaned, polished and etched the blade.

I used some circuit board etching solution about 50/50 strength for about 30 minutes. Next I lightly wire brushed it by hand and applied a coating of Renaissance Wax to the lightly heated blade.

When it was room temp I buffed it by hand with a cloth to bring up a bit of luster.

This was my first try at blade etching, so comments and suggestions welcome!

estcrh · 9th September 2014, 05:45 AM

The difference in impressive.

Aleksey · 9th September 2014, 09:13 AM

Could you tell the exact dimensions of the knife?

Then were there 2 holes to insert chopsticks into the scabbard on the outer side of scabbard?

RSWORD · 9th September 2014, 12:59 PM

It turned out very nicely. I didn't realize it was a double edged blade. The result is similar to what you would get on a good Jian blade. The two edges show the hardened edge and then you have the central core softer steel that reveals the nice lamination. It has a sort of wood grain effect. The hardened edge zones appear like the hamon from a Japanese sword. Same basic concept so no surprise there. Hard edge. Soft body. This creates a very hard and sharp edge that isn't too brittle because of the flexibility the softer core provides when you strike something. Hence its ability to chop into wood without chipping or breaking.

Shakethetrees · 9th September 2014, 02:41 PM

It chopped steel!

I wouldn't believe it unless I saw it!

blue lander · 23rd August 2015, 03:57 AM

I just showed your knife to a room full of Mongolian men. They confirmed it was Mongolian but that it was a "killers knife" and that I should not buy it under any circumstances.

Shakethetrees · 23rd August 2015, 07:32 AM

Interesting.

What else did they say about it?

blue lander · 24th August 2015, 01:08 AM

They barely spoke any English , but they seemed to think that the hilt and scabbard were supposed to look like a regular Mongolian single edged knife that everyone used to wear so you could carry it without raising suspicion.

9th September 2014, 05:07 AM	#1
Shakethetrees Member Join Date: Apr 2014 Location: Louisiana Posts: 363	Polished and etched! I had a little time on my hands today and cleaned, polished and etched the blade. I used some circuit board etching solution about 50/50 strength for about 30 minutes. Next I lightly wire brushed it by hand and applied a coating of Renaissance Wax to the lightly heated blade. When it was room temp I buffed it by hand with a cloth to bring up a bit of luster. This was my first try at blade etching, so comments and suggestions welcome! Attached Images

9th September 2014, 05:45 AM	#2
estcrh Member Join Date: Jun 2012 Location: USA Posts: 1,492	The difference in impressive. Attached Images

9th September 2014, 09:13 AM	#3
Aleksey Member Join Date: Aug 2014 Posts: 15	Could you tell the exact dimensions of the knife? Then were there 2 holes to insert chopsticks into the scabbard on the outer side of scabbard?

9th September 2014, 12:59 PM	#4
RSWORD Member Join Date: Dec 2004 Location: Greensboro, NC Posts: 1,093	It turned out very nicely. I didn't realize it was a double edged blade. The result is similar to what you would get on a good Jian blade. The two edges show the hardened edge and then you have the central core softer steel that reveals the nice lamination. It has a sort of wood grain effect. The hardened edge zones appear like the hamon from a Japanese sword. Same basic concept so no surprise there. Hard edge. Soft body. This creates a very hard and sharp edge that isn't too brittle because of the flexibility the softer core provides when you strike something. Hence its ability to chop into wood without chipping or breaking.

9th September 2014, 02:41 PM	#5
Shakethetrees Member Join Date: Apr 2014 Location: Louisiana Posts: 363	It chopped steel! I wouldn't believe it unless I saw it!

23rd August 2015, 03:57 AM	#6
blue lander Member Join Date: Nov 2013 Posts: 456	I just showed your knife to a room full of Mongolian men. They confirmed it was Mongolian but that it was a "killers knife" and that I should not buy it under any circumstances.

23rd August 2015, 07:32 AM	#7
Shakethetrees Member Join Date: Apr 2014 Location: Louisiana Posts: 363	Interesting. What else did they say about it?

24th August 2015, 01:08 AM	#8
blue lander Member Join Date: Nov 2013 Posts: 456	They barely spoke any English , but they seemed to think that the hilt and scabbard were supposed to look like a regular Mongolian single edged knife that everyone used to wear so you could carry it without raising suspicion.