Visayan daga/sword/kris for comment

Ferguson · 19th August 2013, 08:54 PM

Don't dispair Detlef. It's still a wonderful piece, even with the grinder marks. With some fine sandpaper, P220 or finer, you can sand along the length of the sword until most of the marks are gone. then move to a finer grit, maybe 320 then 400 then 600. This will be very tedious, and will take some hours. But it can be done. Some may say to do nothing, and I might agree.

Good luck!

Steve

Edit: While I was composing my post, I see that others whom I respect very much suggested doing nothing. It is your decision.

Sajen · 19th August 2013, 09:57 PM

Thank you for your kind words Robert, Ian and Steve. When it only would be the grinder marks I would try to follow Steve's advice but the person who have done this has let areas where he has changed the profile of the blade (see pictures) and I really think that there is nothing what I can do to withdraw this. The shown areas are only a few examples. It's a real shame.

Sajen · 2nd July 2014, 09:43 PM

Have get back the "kris" from a friend who is a master of blade restauration. He has worked out all the grinder marks, polished and etched the blade and has given back the blade it's beauty. The blade shows a very nice lamination and now I will try to replace the missing silver plates at the handle.
Here some pictures for sharing.

Robert · 2nd July 2014, 10:31 PM

Detlef, Your friend did an amazing job on this blade restoration. When I first started looking at the new photos I was worried that the medial ridge had been lost in the process of reworking the blade, but after I finished looking at them all I was happy to see that was not the case. Even though this is not what I would have done if this were mine I must say your friend did a great job of giving new life to an old and neglected warrior in desperate need of some TLC.

Best,
Robert

Sajen · 2nd July 2014, 10:54 PM

Quote:

Originally Posted by Robert

Detlef, Your friend did an amazing job on this blade restoration. When I first started looking at the new photos I was worried that the medial ridge had been lost in the process of reworking the blade, but after I finished looking at them all I was happy to see that was not the case. Even though this is not what I would have done if this were mine I must say your friend did a great job of giving new life to an old and neglected warrior in desperate need of some TLC.

Best,
Robert

Hello Robert,

agree with you that he did an amazing job. I have had the same worries that the blade will lost the cental ridge by reworking so I never would have tried to do it byself but he was sure get back the original contour of the blade. When you handle the blade now you never will get the idea that it was in such a bad condition. And you still can see that it is an antique blade.

Regards,
Detlef

Battara · 3rd July 2014, 04:32 AM

I love the laminations in the blade!

19th August 2013, 09:57 PM	#2
Sajen Member Join Date: Aug 2007 Location: Germany, Dortmund Posts: 9,490	Thank you for your kind words Robert, Ian and Steve. When it only would be the grinder marks I would try to follow Steve's advice but the person who have done this has let areas where he has changed the profile of the blade (see pictures) and I really think that there is nothing what I can do to withdraw this. The shown areas are only a few examples. It's a real shame. Attached Images

2nd July 2014, 09:43 PM	#3
Sajen Member Join Date: Aug 2007 Location: Germany, Dortmund Posts: 9,490	Have get back the "kris" from a friend who is a master of blade restauration. He has worked out all the grinder marks, polished and etched the blade and has given back the blade it's beauty. The blade shows a very nice lamination and now I will try to replace the missing silver plates at the handle. Here some pictures for sharing. Attached Images

19th August 2013, 08:54 PM	#1
Ferguson Member Join Date: Dec 2004 Location: Kernersville, NC, USA Posts: 793	Don't dispair Detlef. It's still a wonderful piece, even with the grinder marks. With some fine sandpaper, P220 or finer, you can sand along the length of the sword until most of the marks are gone. then move to a finer grit, maybe 320 then 400 then 600. This will be very tedious, and will take some hours. But it can be done. Some may say to do nothing, and I might agree. Good luck! Steve Edit: While I was composing my post, I see that others whom I respect very much suggested doing nothing. It is your decision.

2nd July 2014, 10:31 PM	#4
Robert (deceased) Join Date: Feb 2005 Location: Centerville, Kansas Posts: 2,196	Detlef, Your friend did an amazing job on this blade restoration. When I first started looking at the new photos I was worried that the medial ridge had been lost in the process of reworking the blade, but after I finished looking at them all I was happy to see that was not the case. Even though this is not what I would have done if this were mine I must say your friend did a great job of giving new life to an old and neglected warrior in desperate need of some TLC. Best, Robert

3rd July 2014, 04:32 AM	#6
Battara EAAF Staff Join Date: Dec 2004 Location: Louisville, KY Posts: 7,363	I love the laminations in the blade!