tulwar or talwar

Rick · 12th June 2005, 02:03 AM

Henk , the only thing I would check is if these blades have been varnished or lacquered ; if they have then I would think that removing the old applied finish would be acceptable .
Then I would apply Rennaisance Wax as a substitute .

As you probably know it was not unusual for collectors of earlier times to varnish or lacquer their pieces to prevent rusting .

They are all beauties .

IMO sharpening shows an active career for the sword .

Andrew · 12th June 2005, 05:00 AM

Henk,

Is the straight-bladed example edged on both sides or is it a "back sword", edged only on one? Is it sharpened at all?

The tulwar hilt is not condusive to the thrust with a straight blade, as it doesn't permit the wrist extension necessary. I'm puzzled by the mating of what appears to be a thrusting blade with this form of hilt.

Thank you for sharing these with us, Henk.

tom hyle · 12th June 2005, 07:59 AM

Mind you it's pretty dandy for a backhanded thrust of the sort that can be sent around a sheild.

Henk · 12th June 2005, 11:20 AM

Gentlemen,

First I want to thank you all for your input. I was struck by these three tulwars and the kukri in the box. The other stuff was with it.

Jens,

For your information, and it is not allowed to mention prices, when I devide the total amount to the 10 pieces I bought I could tell the Mrs. that it was a bargain

Please give me some time to make the pictures you're required. Maybe tonight I have some time to spare or tomorrow. But I will make them.

The three copper dots are in a row. From the first dot to the last one, you can divide the distance in three sections. The first dot is under the hilt in the middle of the blade. The second one is two/third lower towards the tip against the back of the blade and the last one is on one/third distance from the previous one in the tip. The first and the last dot are visible on the pics.

This one is certainly my favorite, just as the third one is.

M.Carter,

The hilts are not loose. Only the cap from the second one was conected with a wedge in the pommel. That wedge is gone so i have to try to make a substitute. Maybe a metal one. That's the only point, but all three are battle ready.

Rick,

All three the blades have been sharpened. The first and the second one on the entire edge. The third one only the point. Just like it was used for fenching. The patina of the first and the second one is "original" and no spurs of varnish or lacquer. The third one is lacquered and should be cleaned. Any ideas what the most safest way is to remove the lacquer? I really wish to threat them as babys.

Last but not least, Andrew,

The straight bladed one is edged on both sides. As mentioned above it is sharpened on the tip.
These kind of blades with such a hilt were called "Firangi" according to Stone.
But these weapons used to have a khanda hilt. If i compare a khanda hilt to a tulwar hilt, the main difference is the spike at the end of the pommel. If i look to the end of the pommels of the first and the second one, they are finished off very well with a round knob. It looks to me that some idio... took a metallsaw to cut off the large end because it didn't fit into his ....???

Aparently the sawing work is finished off with a hammer to get rid of the sharp edges that remains after the sawing. I will also try to catch this in a picture. In my opinion this one is really abused by some ........

It's my pleasure to share these ones with you and learn about it.

Andrew · 12th June 2005, 05:08 PM

Quote:

Originally Posted by Henk

Last but not least, Andrew,

The straight bladed one is edged on both sides. As mentioned above it is sharpened on the tip.
These kind of blades with such a hilt were called "Firangi" according to Stone.
But these weapons used to have a khanda hilt. If i compare a khanda hilt to a tulwar hilt, the main difference is the spike at the end of the pommel. If i look to the end of the pommels of the first and the second one, they are finished off very well with a round knob. It looks to me that some idio... took a metallsaw to cut off the large end because it didn't fit into his ....???

Aparently the sawing work is finished off with a hammer to get rid of the sharp edges that remains after the sawing. I will also try to catch this in a picture. In my opinion this one is really abused by some ........

It's my pleasure to share these ones with you and learn about it.

As I understand it, "firangi" refers to any foreign-bladed Indian sword. If this is, indeed, a European rapier blade, then it would certainly be a firangi.

It just seems like an unlikely mating of handle/blade.

Henk · 12th June 2005, 05:35 PM

You're right Andrew. When I quote Stone: "FIRANGI, FARANG, PHIRANGI. Literally the Portugese, or foreigner. A Mahratta cut-and-thrust, straight bladed sword. The blades were either imported from Europe by the Portugese, or made in imitation of them. Broadsword blades with either three or four shallow grooves were the most common, but rapier blades were also used.The hilts were of the khanda type, with broad guards, and disk pommels with curved spikes on them. Most of the blades are of the 17th century, though some are of the 16th."

Jens Nordlunde · 12th June 2005, 05:40 PM

Hmm, yes well Andrew, I think it is a yes and a no. True that farangi refers to Indian swords with a foreign blade – and this blade surely is foreign – but farangis have khanda hilts, not tulwar hilts, and this is, I think a special tulwar hilt on top of it all, we will see when we get more pictures. What makes a farangi a farangi? Is it the blade or the blade and the hilt? I think we can agree on that a khanda hilt with a foreign blade is a farangi, and maybe this one is too, but it is most unusual to see a blade like this with an unusual tulwar hilt – is this a farangi? Maybe you are right, but I am not quite convinced at the moment.

Henk · 12th June 2005, 05:54 PM

Jens,

Here are the pics of the "firangi" to give this one a name. Is this what you mean and good enough to see something? I'd better first ask before i launch the other pics i made. If not I have to try to make better ones but it isn't easy with flashlight and i'm not a prof.

Jeff D · 12th June 2005, 05:54 PM

I am glad I am not the only one confused on the definition of farangi. I have used the term as Andrew has stated, that being a straight bladed broad sword or backsword, usually with the Hindu basket but not necessarily. I think Andy has posted one with a rapier blade on SFI, for lack of any other term I would also call it a Farangi.

Jeff

Andrew · 12th June 2005, 04:58 PM

Quote:

Originally Posted by tom hyle

Mind you it's pretty dandy for a backhanded thrust of the sort that can be sent around a sheild.

No doubt. But wouldn't you rather have a curved saber for that particular thrust?

tom hyle · 12th June 2005, 11:50 PM

Quote:

Originally Posted by Andrew

No doubt. But wouldn't you rather have a curved saber for that particular thrust?

Absolutely; like, for instance, a tulwar. I was just clarifying that the tulwar hilt is not bad for thrusting, just bad for one type of thrusting; the one that's commonly and incorrectly treated as the only one in European training.
Interesting the diversity of opinion on the obstructionism or nonobstructionism of the tulwar pommel. If the grip fits your hand (this is after all important), and the pommel hurts you it's because you're using motions meant for/learnt from other swords. you don't snap your wrist when cutting with a tulwar as you can with many swords; you can't. You have to slash; it will not permit a hack. This may be meant to enforce proper cutting for greater affect, but also may foster a technique less liable to damage the wrist and/or lose the sword when cutting from horseback.

tom hyle · 12th June 2005, 11:55 PM

On tulwar hilt vs khanda hilt, AFAIK the "spike" (it's really a handle for left hand flips and long ones can be used in blocks though I don't know if that's traditional) is not the only difference, and like some others is not universal (ie some tulwars do have a long "spike".). There is the grip, curved and cylindrical on the firangi, straight and swelled on the tulwar (yes, another nonuniversal). There is the flat plate quard, with its boatlike upward curve that seems greater than the cupping affect of a tulwar's quillons, and the quillons under the plate, with their resemblance to the ganga of kris sundang (and often with baca like features). There are the superlong and often rivetted down lagnets, which are probably the biggest difference. There is the angle of the pommel; more often more forward on firangi or khanda than on tulwar.

Rick · 13th June 2005, 02:19 AM

Gosh , I go out to dinner and I come back to multi forum mayhem .

IMO a tulwar is used for a thrust in a bent arm position with the elbow as the main joint used . You do not see very many tulwars IIRC with that acute of a point , and the tulwar is not used as an epee or smallsword would be . I think that it is more for an Indian style of swordsmanship (draw cut) as Mark mentions than any Western style .
[addendum the tulwar I have been trying moves with is practically straight]
http://www.oriental-arms.com/item.php?id=1048
As a side note or a parallel example if you will ; I have an old Moro multi waved kris . When I first got it I looked down the length of the blade and saw that it had a slight twist . At first I thought it was an inadvertent flaw by the panday , then after playing around with it I came to the realization that it had been put in on purpose so that the angle of the cut was naturally adjusted for the wavy style of blade .

Yes, I take a medium glove so that would mean that my mitts are smaller than average , but I have really long fingers .

12th June 2005, 05:35 PM	#6
Henk Member Join Date: Dec 2004 Location: The Netherlands Posts: 1,209	You're right Andrew. When I quote Stone: "FIRANGI, FARANG, PHIRANGI. Literally the Portugese, or foreigner. A Mahratta cut-and-thrust, straight bladed sword. The blades were either imported from Europe by the Portugese, or made in imitation of them. Broadsword blades with either three or four shallow grooves were the most common, but rapier blades were also used.The hilts were of the khanda type, with broad guards, and disk pommels with curved spikes on them. Most of the blades are of the 17th century, though some are of the 16th." Attached Images Last edited by Henk; 12th June 2005 at 05:56 PM.

12th June 2005, 05:54 PM	#8
Henk Member Join Date: Dec 2004 Location: The Netherlands Posts: 1,209	Jens, Here are the pics of the "firangi" to give this one a name. Is this what you mean and good enough to see something? I'd better first ask before i launch the other pics i made. If not I have to try to make better ones but it isn't easy with flashlight and i'm not a prof. Attached Images

12th June 2005, 02:03 AM	#1
Rick Vikingsword Staff Join Date: Nov 2004 Posts: 6,376	Henk , the only thing I would check is if these blades have been varnished or lacquered ; if they have then I would think that removing the old applied finish would be acceptable . Then I would apply Rennaisance Wax as a substitute . As you probably know it was not unusual for collectors of earlier times to varnish or lacquer their pieces to prevent rusting . They are all beauties . IMO sharpening shows an active career for the sword .

12th June 2005, 05:00 AM	#2
Andrew Member Join Date: Nov 2004 Location: USA Posts: 1,725	Henk, Is the straight-bladed example edged on both sides or is it a "back sword", edged only on one? Is it sharpened at all? The tulwar hilt is not condusive to the thrust with a straight blade, as it doesn't permit the wrist extension necessary. I'm puzzled by the mating of what appears to be a thrusting blade with this form of hilt. Thank you for sharing these with us, Henk.

12th June 2005, 07:59 AM	#3
tom hyle Member Join Date: Dec 2004 Location: Houston, TX, USA Posts: 1,254	Mind you it's pretty dandy for a backhanded thrust of the sort that can be sent around a sheild.

12th June 2005, 11:20 AM	#4
Henk Member Join Date: Dec 2004 Location: The Netherlands Posts: 1,209	Gentlemen, First I want to thank you all for your input. I was struck by these three tulwars and the kukri in the box. The other stuff was with it. Jens, For your information, and it is not allowed to mention prices, when I devide the total amount to the 10 pieces I bought I could tell the Mrs. that it was a bargain Please give me some time to make the pictures you're required. Maybe tonight I have some time to spare or tomorrow. But I will make them. The three copper dots are in a row. From the first dot to the last one, you can divide the distance in three sections. The first dot is under the hilt in the middle of the blade. The second one is two/third lower towards the tip against the back of the blade and the last one is on one/third distance from the previous one in the tip. The first and the last dot are visible on the pics. This one is certainly my favorite, just as the third one is. M.Carter, The hilts are not loose. Only the cap from the second one was conected with a wedge in the pommel. That wedge is gone so i have to try to make a substitute. Maybe a metal one. That's the only point, but all three are battle ready. Rick, All three the blades have been sharpened. The first and the second one on the entire edge. The third one only the point. Just like it was used for fenching. The patina of the first and the second one is "original" and no spurs of varnish or lacquer. The third one is lacquered and should be cleaned. Any ideas what the most safest way is to remove the lacquer? I really wish to threat them as babys. Last but not least, Andrew, The straight bladed one is edged on both sides. As mentioned above it is sharpened on the tip. These kind of blades with such a hilt were called "Firangi" according to Stone. But these weapons used to have a khanda hilt. If i compare a khanda hilt to a tulwar hilt, the main difference is the spike at the end of the pommel. If i look to the end of the pommels of the first and the second one, they are finished off very well with a round knob. It looks to me that some idio... took a metallsaw to cut off the large end because it didn't fit into his ....??? Aparently the sawing work is finished off with a hammer to get rid of the sharp edges that remains after the sawing. I will also try to catch this in a picture. In my opinion this one is really abused by some ........ It's my pleasure to share these ones with you and learn about it.

12th June 2005, 05:40 PM	#7
Jens Nordlunde Member Join Date: Dec 2004 Location: Europe Posts: 2,718	Hmm, yes well Andrew, I think it is a yes and a no. True that farangi refers to Indian swords with a foreign blade – and this blade surely is foreign – but farangis have khanda hilts, not tulwar hilts, and this is, I think a special tulwar hilt on top of it all, we will see when we get more pictures. What makes a farangi a farangi? Is it the blade or the blade and the hilt? I think we can agree on that a khanda hilt with a foreign blade is a farangi, and maybe this one is too, but it is most unusual to see a blade like this with an unusual tulwar hilt – is this a farangi? Maybe you are right, but I am not quite convinced at the moment.

12th June 2005, 05:54 PM	#9
Jeff D Member Join Date: Dec 2004 Location: B.C. Canada Posts: 473	I am glad I am not the only one confused on the definition of farangi. I have used the term as Andrew has stated, that being a straight bladed broad sword or backsword, usually with the Hindu basket but not necessarily. I think Andy has posted one with a rapier blade on SFI, for lack of any other term I would also call it a Farangi. Jeff

12th June 2005, 11:55 PM	#12
tom hyle Member Join Date: Dec 2004 Location: Houston, TX, USA Posts: 1,254	On tulwar hilt vs khanda hilt, AFAIK the "spike" (it's really a handle for left hand flips and long ones can be used in blocks though I don't know if that's traditional) is not the only difference, and like some others is not universal (ie some tulwars do have a long "spike".). There is the grip, curved and cylindrical on the firangi, straight and swelled on the tulwar (yes, another nonuniversal). There is the flat plate quard, with its boatlike upward curve that seems greater than the cupping affect of a tulwar's quillons, and the quillons under the plate, with their resemblance to the ganga of kris sundang (and often with baca like features). There are the superlong and often rivetted down lagnets, which are probably the biggest difference. There is the angle of the pommel; more often more forward on firangi or khanda than on tulwar.

13th June 2005, 02:19 AM	#13
Rick Vikingsword Staff Join Date: Nov 2004 Posts: 6,376	Gosh , I go out to dinner and I come back to multi forum mayhem . IMO a tulwar is used for a thrust in a bent arm position with the elbow as the main joint used . You do not see very many tulwars IIRC with that acute of a point , and the tulwar is not used as an epee or smallsword would be . I think that it is more for an Indian style of swordsmanship (draw cut) as Mark mentions than any Western style . [addendum the tulwar I have been trying moves with is practically straight] http://www.oriental-arms.com/item.php?id=1048 As a side note or a parallel example if you will ; I have an old Moro multi waved kris . When I first got it I looked down the length of the blade and saw that it had a slight twist . At first I thought it was an inadvertent flaw by the panday , then after playing around with it I came to the realization that it had been put in on purpose so that the angle of the cut was naturally adjusted for the wavy style of blade . Yes, I take a medium glove so that would mean that my mitts are smaller than average , but I have really long fingers .