Irish Pistol with bayonet

Ken Maddock · 19th January 2015, 09:04 PM

While I had the camera out I took a few photos of another gun with a bayonet
Again this is an irish one
This one was made in Dublin by the prominent sword maker J Read of Parliament street
You can also see Dublin registration mark
DU 1442 on the barrel

Lovely little pistol with barrel unscrewing and all mechanism working
Bayonet is released by pulling back on trigger guard
Hope you like this gun, picked it up in a junk shop for less than 2 take out pizzas

All the best
K

Shakethetrees · 19th January 2015, 10:27 PM

Congratulations, Ken, I'm really really jealous!

Nice pistol!

Ken Maddock · 20th January 2015, 07:58 AM

Thanks for compliment
Just forgot to mention one thing
The box and powder flask are not original to the pistol, the box is an old traveling balance box, ground it in a car boot sale and reckoned it would work which it thankfully did. The flask is an auction pick up which I think matches. Bullet mould has yet to be found
Regards
Ken

fernando · 20th January 2015, 03:55 PM

Nice pistol Ken !
... and with the barrel still being possible to unscrew, which so often isn't.
You must tell me where that junk shop is about

Ken Maddock · 21st January 2015, 11:01 AM

Hi Fernando
Thanks for the comments,
I like this little guy as well, very well made and even the safety works
It was very rusty when I got it but complete
It all had to be opened up and taken apart
I even had to resort to a oxy acetylene blow torch to free up some of the parts
The barrel was not budging at all
My method was (first check gun not loaded)
soak barrel in penetrating oil
get a concrete expanding bolt wrap it in rag (to save on the scratches) and insert into the barrel and open it out by screwing in the bolt. then you have something you can hold very tight with a vice grip

the back of lock vice is held in a padded vice, careful not to hold onto the handle as this would not support any tourque. hold as close to the barrel as possible as you do not want the heat de tempering the springs in the gun
then try to twist off the barrel,
if it does not come a bit of heat always helps.
sometimes there is no success and barrel remains locked and removing the bolt can be difficult but is doable, I have had to resort to burning out the rag to help remove the bolt but only once.
Hope this works for you when needed
regards
ken

fernando · 21st January 2015, 12:56 PM

Ah, i wouldn't have both some of those tools and the hands (

) ... besides the fear that the heating part would damage things.
I have tried to turn my stuck up ones with a padded grip and i didn't manage to convince them.
So i called it an end

... But thanks a lot for the comprehensive instructions; it's always good to know

.

19th January 2015, 09:04 PM	#1
Ken Maddock Member Join Date: Aug 2013 Location: Ireland Posts: 104	Irish Pistol with bayonet While I had the camera out I took a few photos of another gun with a bayonet Again this is an irish one This one was made in Dublin by the prominent sword maker J Read of Parliament street You can also see Dublin registration mark DU 1442 on the barrel Lovely little pistol with barrel unscrewing and all mechanism working Bayonet is released by pulling back on trigger guard Hope you like this gun, picked it up in a junk shop for less than 2 take out pizzas All the best K Attached Images

21st January 2015, 12:56 PM	#6
fernando Lead Moderator European Armoury Join Date: Dec 2004 Location: Portugal Posts: 9,639	Ah, i wouldn't have both some of those tools and the hands () ... besides the fear that the heating part would damage things. I have tried to turn my stuck up ones with a padded grip and i didn't manage to convince them. So i called it an end ... But thanks a lot for the comprehensive instructions; it's always good to know .

19th January 2015, 10:27 PM	#2
Shakethetrees Member Join Date: Apr 2014 Location: Louisiana Posts: 363	Congratulations, Ken, I'm really really jealous! Nice pistol!

20th January 2015, 07:58 AM	#3
Ken Maddock Member Join Date: Aug 2013 Location: Ireland Posts: 104	Thanks for compliment Just forgot to mention one thing The box and powder flask are not original to the pistol, the box is an old traveling balance box, ground it in a car boot sale and reckoned it would work which it thankfully did. The flask is an auction pick up which I think matches. Bullet mould has yet to be found Regards Ken

20th January 2015, 03:55 PM	#4
fernando Lead Moderator European Armoury Join Date: Dec 2004 Location: Portugal Posts: 9,639	Nice pistol Ken ! ... and with the barrel still being possible to unscrew, which so often isn't. You must tell me where that junk shop is about

21st January 2015, 11:01 AM	#5
Ken Maddock Member Join Date: Aug 2013 Location: Ireland Posts: 104	Hi Fernando Thanks for the comments, I like this little guy as well, very well made and even the safety works It was very rusty when I got it but complete It all had to be opened up and taken apart I even had to resort to a oxy acetylene blow torch to free up some of the parts The barrel was not budging at all My method was (first check gun not loaded) soak barrel in penetrating oil get a concrete expanding bolt wrap it in rag (to save on the scratches) and insert into the barrel and open it out by screwing in the bolt. then you have something you can hold very tight with a vice grip the back of lock vice is held in a padded vice, careful not to hold onto the handle as this would not support any tourque. hold as close to the barrel as possible as you do not want the heat de tempering the springs in the gun then try to twist off the barrel, if it does not come a bit of heat always helps. sometimes there is no success and barrel remains locked and removing the bolt can be difficult but is doable, I have had to resort to burning out the rag to help remove the bolt but only once. Hope this works for you when needed regards ken