Ethnographic Arms & Armour
 

Go Back   Ethnographic Arms & Armour > Discussion Forums > Ethnographic Weapons

Reply
 
Thread Tools Search this Thread Display Modes
Old 15th December 2013, 09:11 PM   #1
DaveS
Member
 
Join Date: Feb 2006
Posts: 327
Default Damascus Kaskara

Here is a damascus kaskara for viewing. The blade is layered damascus
with what is left of three fullers, 34 inches long, 40 inches overall with a
silver handle. Some of the inscription on the blade is in Latin. I tried my best
to photograph these and the figures, but i don't think they came out too
clearly. The scabbard is in absolutely pristine condition with all the goodies.
Any ideas as to age or origin. I also have another damascus kaskara
with a single wide fuller down the entire length of the blade. These kaskara
blades must be rare, as these are the only two that i've ever seen......Dave.
Attached Images
          
DaveS is offline   Reply With Quote
Old 15th December 2013, 09:30 PM   #2
A.alnakkas
Member
 
A.alnakkas's Avatar
 
Join Date: Nov 2010
Location: Kuwait
Posts: 1,336
Default

a fine piece! though I have a feeling that this was not meant to be etched.
A.alnakkas is offline   Reply With Quote
Old 16th December 2013, 12:25 AM   #3
DaveS
Member
 
Join Date: Feb 2006
Posts: 327
Default Damascus Kaskara

A.alnakkas: This is the way it was when i accquired it, already etched.
I would think that the smith would want the blade etched to show
his skill. Just a thought.........Dave.
DaveS is offline   Reply With Quote
Old 16th December 2013, 12:38 AM   #4
kino
Member
 
kino's Avatar
 
Join Date: Dec 2004
Posts: 966
Default

That's nice Dave!
Is it a European blade?
I have seen pattern welded European swords, one being a German Naval sword.
kino is offline   Reply With Quote
Old 16th December 2013, 03:15 AM   #5
DaveS
Member
 
Join Date: Feb 2006
Posts: 327
Default Damascus Kaskara

Hi Albert: Yes, there is no doubt in my mind that it is a european blade. I
think it is a much older blade also, because i would think that the
mass produced ones made later for export would not be layered. It
would be too time consuming. You can see that the three narrow
fullers are almost washed out due to many years of cleaning and
maintainence............Dave.
P.S......Say hi to Bonny
DaveS is offline   Reply With Quote
Old 16th December 2013, 04:20 AM   #6
Jim McDougall
Arms Historian
 
Jim McDougall's Avatar
 
Join Date: Dec 2004
Location: Route 66
Posts: 9,719
Default

Now here is an anomaly! The blade profile is very much as seen in many native produced blades for kaskara, but I cannot think of ever seeing any which were 'Damascus'. I'm sure those here with metallurgical expertise might give better account of this case, but I do not believe this is a European blade. While as noted there may have been instances of pattern welded blades in European context they are not among the 'trade blades' which entered the North African sphere.

The mounts appear to be of modern 'Kasallawi' style which are produced in this area of Sudan from around 1960s as I understand (Reed, 1987) and often associated with Darfur. These blades were of course remounted many times over generations so using them to assess the blade age is often counterproductive.

What is most curious are the engraved intaglio and angelic figure devices on the blade which are typically regarded as in the "Caissagnard' style and usually found on French blades on court swords, smallswords and hangers of mid to end of 18th century. As this type blade, and certainly not pattern welded or damascened was not in use in European swords at this time nor later it would seem that perhaps these engravings were copied on this blade by a quite skilled artisan in native trade entrepots.

Just my thoughts and as always very much look forward to other views.
Jim McDougall is offline   Reply With Quote
Old 16th December 2013, 05:57 AM   #7
DaveS
Member
 
Join Date: Feb 2006
Posts: 327
Default Damascus Kaskara

Jim: I have some kaskaras with native made blades and none are of the
same quality as this one. Has anyone on the forum seen a damascus
blade that was done by a North-African smith? The North-African swords
swords i have seen and the ones i own don't exhibit any damascus at all.
It's hard to tell in the pictures, but the layer-welded pattern is of
very high quality, almost similar to a couple of straight bladed Indian
swords that i have. Could this blade be a trade blade from the Indian
market, and the markings be put on locally?.........Dave.
DaveS is offline   Reply With Quote
Old 16th December 2013, 05:47 PM   #8
Jim McDougall
Arms Historian
 
Jim McDougall's Avatar
 
Join Date: Dec 2004
Location: Route 66
Posts: 9,719
Default

That is an interesting question Dave, and actually India did play a part in some degree in weapons and blades which entered the Red Sea trade and I believe came into the Anglo-Egyptian Sudan and environs through various entrepots . However, in these cases the blades were typically European which had filtered through their trade routes as far as I have understood.

It must be remembered that these type broadsword blades did not correspond to any weapon form used in India, and India did not produce blades for export, again as far as I have known. It does seen that other anomalies such as backsword blades, European cavalry types, have occasionally appeared on kaskara, a match which does see to strongly suggest India as these kinds of blades occur on firangi's.

Conversely, I have seen kaskara type blades on Indian pata, again, usually European types (three center fullers) and by the same token, North African smiths did not produce for export.

You say you have two of these Damascus blades! That may be key to further research on these blades and it would be excellent if you could get some better images (though what you have furnished is good). If you could get the two fully described as far as fullering etc.and dimensions (again, as you have already nicely done on this one).

I would offer this, I have seen another curiosity, which is a short saber and mounted in a brass Ottoman style hilt with deeply embossed lozenge pattern
crosshatch overall. The guard is with Ottoman style crossguard but with distinctly 'kaskara' form langet. It is mounted in the Sudanese style with flared tip scabbard . Most importantly, the steel in the blade I believe was referred to as something termed 'Turkish beyez(?) ' and was some type of patterned steel . If there were Ottoman smiths producing such hybrid items, probably during the 'Condominium' , where French as well as of course the British were occupiers post Omdurman, it would seem an ideal context for such a blade. Further, the application of these French occult oriented images would seem more plausibly situated.

I hope we will see Chris and Iain join in here as their concentrated and advanced studies and research on these arms may have better answers.
In any case, than you so much for posting this, and the opportunity to look deeper into this unusual example.
Jim McDougall is offline   Reply With Quote
Old 16th December 2013, 07:36 PM   #9
Edster
Member
 
Join Date: Oct 2010
Posts: 389
Default

Dave,

Very interesting kaskara. I can't comment on the blade material, but can offer some observations. The cross-guard is flared, and likely at least early-mid 20th century. The scabbard, though very high quality is likely a more modern addition since it shows almost no use. The bulbous profile is not as rounded as seen in the east. The tip and the band at the scabbard opening are likely silver, but appear relatively plain and not in keeping with the overall quality of the scabbard. Also, the two "flaps" are five-sided as opposed to the normally seen triangular ones common on Eastern Sudan examples. The engravings are similar to those described by Reed (Attached for reference). Also, the angel has wings and breasts, not likely to be of Muslim origin, but as Jim suggests perhaps French occult. Can you translate the Latin text?

My guess its origins are Western Sudan, Dar Fur or maybe Chad.

Ed
Attached Images
File Type: pdf Kaskara from Northern Darfur (2)_Kwon Compressed.pdf (1.02 MB, 632 views)
Edster is offline   Reply With Quote
Old 16th December 2013, 10:37 PM   #10
David R
Member
 
David R's Avatar
 
Join Date: Jan 2011
Posts: 1,048
Default

A lot of older European blades are made out of "Shear Steel" a forged and folded steel that was not intended to be etched, but shows a watered pattern on those occasions when it is. It is possibly one of these.
David R is offline   Reply With Quote
Old 17th December 2013, 02:31 AM   #11
DaveS
Member
 
Join Date: Feb 2006
Posts: 327
Default Damascus Kaskara

David R: I've heard of shear steel but don't know what it would like in a
sword blade that has been etched. I can tell you that this blade is
a layer-weld that was made to be etched and seen. I know it is
hard to tell by the quality of these pictures, but once the blade is
in hand and one can get a first hand look, it is very apparent that
this was a pattern that was brought out so it could be appreciated
by it's owner.
On the other hand i'm going to post pictures of the other kaskara
that has a pattern that looks like a layer weld, but i can't be 100
percent positive that it is damascus. Maybe it is "shear steel". It
almost reminds me a little of Syrian wootz (Sham). It has a little
shimmery look to it like sham, but of course it's not sham. Darn!!!
wish it was.............Dave
DaveS is offline   Reply With Quote
Old 17th December 2013, 01:45 PM   #12
Iain
Member
 
Iain's Avatar
 
Join Date: Mar 2010
Location: Olomouc
Posts: 1,680
Default

Regarding shear, Richard Furrer's site has some useful video content regarding the process.

http://www.doorcountyforgeworks.com/Steel_Making.html

As does this thread.
http://www.swordforum.com/forums/sho...r-Steel-Making

Richard is a member here, so if he's inclined to share an opinion I would hope he spots these two kaskara threads.
Iain is offline   Reply With Quote
Old 17th December 2013, 09:53 PM   #13
Emanuel
Member
 
Emanuel's Avatar
 
Join Date: Jul 2005
Location: Toronto, Canada
Posts: 1,242
Default

Hello,

Nice kaskara. The blade is not made from shear steel but purposely pattern welded. Here are two links to 19th century German sabres with "damascus" blades. Seems to have been a fashion at the time.

http://vikingsword.com/vb/showthread.php?t=15333
http://vikingsword.com/vb/showthread.php?t=12784

Emanuel
Emanuel is offline   Reply With Quote
Old 17th December 2013, 10:55 PM   #14
DaveS
Member
 
Join Date: Feb 2006
Posts: 327
Default Damascus Kaskara

Emanuel: Thank you for the links. This clears up some questions that i had.
For sure i knew it was a true layer-weld on this kaskara and the other
one that i posted. I just didn't know where these blades would have
been made. Thanks again........Dave.
DaveS is offline   Reply With Quote
Reply

Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT +1. The time now is 02:52 PM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Posts are regarded as being copyrighted by their authors and the act of posting material is deemed to be a granting of an irrevocable nonexclusive license for display here.