Ethnographic Arms & Armour
 

Go Back   Ethnographic Arms & Armour > Discussion Forums > European Armoury
FAQ Calendar Today's Posts Search

Reply
 
Thread Tools Search this Thread Display Modes
Old 1st January 2015, 03:22 PM   #31
Matchlock
(deceased)
 
Matchlock's Avatar
 
Join Date: Sep 2008
Location: Bavaria, Germany - the center of 15th and 16th century gunmaking
Posts: 4,310
Default

Hi Nando,


Thank you for showing us this specimen.

I think it is notable for contrasting to the earlier stuff on the one hand, and at the same time closely connected with the U.S. ball molds posted above.
Yes, it sure bears witness of heavy use, and I especially like its charming rich patina.

Please allow me to add that the two sharpened scissors right beneath the head were for chopping off the founding nozzle from the ball; this is a remarkable fact because balls keeping that nozzle made binding them to paper cartridges easier.
I reckon that the only kind of fireams which balls retaining their founding neck could not be used with were revolvers.

In the catalog of the latest auction by San Giorgio, Genua, 21 Sept. 2014, I found another mold featuring those scissors.


Attached are images of a rare chest contintaing original paper cartridges for 19th c. U.S. revolvers.


Best,
Michl
Attached Images
            

Last edited by Matchlock; 2nd January 2015 at 06:45 AM.
Matchlock is offline   Reply With Quote
Old 2nd January 2015, 06:32 AM   #32
bkp747
Member
 
bkp747's Avatar
 
Join Date: Jul 2014
Location: Colorado Springs, Colorado
Posts: 15
Default

Great pics. As a shooter, and hand-loader, this adds wonderful insight into the history and traditions of ammunition, and firearms, and... My education continues... Thank you so much
bkp747 is offline   Reply With Quote
Old 2nd January 2015, 12:51 PM   #33
Matchlock
(deceased)
 
Matchlock's Avatar
 
Join Date: Sep 2008
Location: Bavaria, Germany - the center of 15th and 16th century gunmaking
Posts: 4,310
Default

Hi B.,

Since my early childhood days, I have always been a shooter myself. Until about 10 years ago, I used to fire some of my original 400 year-old matchlocks and wheellocks, plus many thousands of rounds from my monstrous heavy .44 cap and ball Colt Walker, my Winchester rifle and my mighty roaring and kicking hard .357 Magnum Colt Single Action Army (SAA) Buntline, with its 16 inch barrel!
Of course, I hand loaded all my muzzleloaders, and I sure made them digest the heaviest loads possible - which they all did.
And, of course, I never harmed any kind of living being.
Against a background of self-experience like this, allow an old "shootist" to just say "Thanks" for appreciating his pictures.

Best,

Michael

Last edited by Matchlock; 3rd January 2015 at 08:31 AM.
Matchlock is offline   Reply With Quote
Old 2nd February 2015, 02:30 PM   #34
ChrisPer
Member
 
Join Date: Sep 2014
Posts: 35
Default

Thank you very much for your experience so generously shared Michael, as well as your excellent pictures.

The usual English term for the founding nozzle is the sprue. When I am casting balls for my muzzleloaders, the sprue cutter in a modern mould is a rotating plate which is knocked sideways to both cut the sprue and unlock the mould blocks. The scissor moulds displayed here would require shears or pincers - even just a sharp knife - to remove the sprues.


As you note above the sprue cone would be ideal to allow a cartridge to be tied off with thread. Another innovation of approximately 1850 by Robert Adams of London for use in percussion revolvers, was to cast a spike on the ball as pictured, and place a greased felt wad on the spike. It was intended that these wads and projectiles be thumbed into the chambers rather than using a larger diameter ball and force it in with a lever rammer. In practice this was unsatisfactory, as the recoil would leave the bullets projecting from the chambers. The innovation was abandoned, then superseded in a few years by cartridge revolvers.
Attached Images
  

Last edited by ChrisPer; 2nd February 2015 at 11:44 PM.
ChrisPer is offline   Reply With Quote
Reply


Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT +1. The time now is 10:44 PM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Posts are regarded as being copyrighted by their authors and the act of posting material is deemed to be a granting of an irrevocable nonexclusive license for display here.