Discoloration and Loss of a Wootz Pattern

Rick · 9th July 2007, 09:08 PM

Here is an example of a light area in wootz.

RSWORD · 10th July 2007, 01:30 AM

I think there are a couple of things that can cause "white spots" in wootz. I think the primary reason is a lack of heat control either during forging or heat treatment of an edge or tip. The other I have noticed can be induced from scabbard wear. A poorly fitted scabbard or one that has shrunk over time can certainly rub on singular spots on the blade and rub away the polish. However, in this case, you can usually still see the pattern beneath the rub spot if angled properly in the light. Certainly any grinders or other equipment used on a wootz blade can overheat the blade and disrupt the pattern as well.

Rick · 10th July 2007, 01:49 AM

I think you're on the right track with this train of thought, Rick .

Gt Obach · 10th July 2007, 12:34 PM

also..
- could be a difference in metal ... martensite will etch dark.. and pearlite is much lighter... ... some times an air jacket will insulate the blade in spots, when you quench it..

- blade wasn't properly degreased before etch... and it protected the blade abit from the acid...... ( smudged finger prints or oils etc )

- a light layer of decarb... left over from forge process.... it will etch very lite and show next to no pattern... or non at all

- burnishing... restoring a blade an using high grit sand paper.... that becomes loded up with steel filings.... this will basically be using steel on steel and burnishing... this does reduce the pattern.... and can be localized...

-sometimes an exta dunk in the etch tank will get rid of this ... as it maybe just some water on the blade that momentarily delays the etch...

looks simple...but lots of things can cause this...

G

9th July 2007, 09:08 PM	#1
Rick Vikingsword Staff Join Date: Nov 2004 Posts: 6,339	Here is an example of a light area in wootz. Attached Images

Thread Tools	Search this Thread
Show Printable Version Email this Page	Search this Thread: Advanced Search
Display Modes
Switch to Linear Mode Hybrid Mode Switch to Threaded Mode

10th July 2007, 01:30 AM	#2
RSWORD Member Join Date: Dec 2004 Location: Greensboro, NC Posts: 1,087	I think there are a couple of things that can cause "white spots" in wootz. I think the primary reason is a lack of heat control either during forging or heat treatment of an edge or tip. The other I have noticed can be induced from scabbard wear. A poorly fitted scabbard or one that has shrunk over time can certainly rub on singular spots on the blade and rub away the polish. However, in this case, you can usually still see the pattern beneath the rub spot if angled properly in the light. Certainly any grinders or other equipment used on a wootz blade can overheat the blade and disrupt the pattern as well.

10th July 2007, 01:49 AM	#3
Rick Vikingsword Staff Join Date: Nov 2004 Posts: 6,339	I think you're on the right track with this train of thought, Rick .

10th July 2007, 12:34 PM	#4
Gt Obach Member Join Date: Mar 2005 Posts: 116	also.. - could be a difference in metal ... martensite will etch dark.. and pearlite is much lighter... ... some times an air jacket will insulate the blade in spots, when you quench it.. - blade wasn't properly degreased before etch... and it protected the blade abit from the acid...... ( smudged finger prints or oils etc ) - a light layer of decarb... left over from forge process.... it will etch very lite and show next to no pattern... or non at all - burnishing... restoring a blade an using high grit sand paper.... that becomes loded up with steel filings.... this will basically be using steel on steel and burnishing... this does reduce the pattern.... and can be localized... -sometimes an exta dunk in the etch tank will get rid of this ... as it maybe just some water on the blade that momentarily delays the etch... looks simple...but lots of things can cause this... G