Taiwan Paiwan Formasa sword/dagger

Maj-Biffy Snodgrass · 26th May 2023, 01:24 PM

I also would suggest a polish and etch , by hand with the right materials and etchant, I'll bet the the outcome will show cold shuts and no lamination but I could be wrong, only one way to find out & that is elbow work and time, do not do it with any modern polishing tool or grinder, if you want good results then polishing by hand with graded polishing papers and WATER not oil is the way to do the job, and the water does not need to be special water, tap, or other will do the job. regards

snody

Maj-Biffy Snodgrass · 26th May 2023, 01:34 PM

One more little and valid observation, the hilt of your knife is shorter than the original early tourist ones that I showed here in attached the pic with identical blade and scabbard, although your scabbard is minus its top curving carved section, so any re hilt with slightly shorter hilt would allow for a washer and peening over of the end of the tang, just an observation but a valid one for sure.
And one question, what are the spacer washers on the top and bottom ends of the hilt made from ??, can you tell which material has been used. regards

Snody.

Copycat · 26th May 2023, 05:47 PM

@Snody

The hilt looks shorter indeed. However, no conclusion can be made if we were to compare length of the hilt alone.

-the tang length of the tourist sword is not visible. It's not surprising if it's really short. It could be too short to peen on a usable hilt.
-the hilts of authentic swords were also short.

The brown spacers are leather. Below are 2 more perfectly fitting brass spacers.

Copycat · 26th May 2023, 06:55 PM

It doesn't look like cast steel. Only cast steel can have cold shut.

It still really looks like forging errors as a result of laminating a blade.

I will post close ups and similar examples later.

Copycat · 26th May 2023, 07:27 PM

First one is the close up of the Taiwan blade. All others are close ups of antiques.

Copycat · 27th May 2023, 09:56 PM

Apologies. I thought I posted a reply.

The tang of the tourist knife is not visible. It is also possible that this tang is too short to peen on a usable hilt. It's not surprising for tourist quality. You only need to glue the tang on the hilt.

The brown spacers are leather. Below are 2 more brass spacers.

Also, cold shuts look different if I were to compare with online examples.

26th May 2023, 01:24 PM	#1
Maj-Biffy Snodgrass Member Join Date: Mar 2023 Posts: 66	agreed Detlef and a very very good idea. I also would suggest a polish and etch , by hand with the right materials and etchant, I'll bet the the outcome will show cold shuts and no lamination but I could be wrong, only one way to find out & that is elbow work and time, do not do it with any modern polishing tool or grinder, if you want good results then polishing by hand with graded polishing papers and WATER not oil is the way to do the job, and the water does not need to be special water, tap, or other will do the job. regards snody

26th May 2023, 01:34 PM	#2
Maj-Biffy Snodgrass Member Join Date: Mar 2023 Posts: 66	hilt and peened tang. One more little and valid observation, the hilt of your knife is shorter than the original early tourist ones that I showed here in attached the pic with identical blade and scabbard, although your scabbard is minus its top curving carved section, so any re hilt with slightly shorter hilt would allow for a washer and peening over of the end of the tang, just an observation but a valid one for sure. And one question, what are the spacer washers on the top and bottom ends of the hilt made from ??, can you tell which material has been used. regards Snody.

26th May 2023, 07:27 PM	#5
Copycat Member Join Date: Apr 2023 Posts: 39	First one is the close up of the Taiwan blade. All others are close ups of antiques. Attached Images

Thread Tools	Search this Thread
Show Printable Version Email this Page	Search this Thread: Advanced Search
Display Modes
Switch to Linear Mode Hybrid Mode Switch to Threaded Mode

26th May 2023, 05:47 PM	#3
Copycat Member Join Date: Apr 2023 Posts: 39	@Snody The hilt looks shorter indeed. However, no conclusion can be made if we were to compare length of the hilt alone. -the tang length of the tourist sword is not visible. It's not surprising if it's really short. It could be too short to peen on a usable hilt. -the hilts of authentic swords were also short. The brown spacers are leather. Below are 2 more perfectly fitting brass spacers.

26th May 2023, 06:55 PM	#4
Copycat Member Join Date: Apr 2023 Posts: 39	It doesn't look like cast steel. Only cast steel can have cold shut. It still really looks like forging errors as a result of laminating a blade. I will post close ups and similar examples later.

27th May 2023, 09:56 PM	#6
Copycat Member Join Date: Apr 2023 Posts: 39	Apologies. I thought I posted a reply. The tang of the tourist knife is not visible. It is also possible that this tang is too short to peen on a usable hilt. It's not surprising for tourist quality. You only need to glue the tang on the hilt. The brown spacers are leather. Below are 2 more brass spacers. Also, cold shuts look different if I were to compare with online examples.