MYSTERY WRITING ON ANCIENT SEAL FOR ID

Vendric · 3rd January 2015, 10:53 PM

The inscription is in cunieform, but this type of writing was used for a number of languages. I see no reason to doubt the antiquity of the item, but admit that my eyesight is not what it once was.

Trent · 4th January 2015, 02:41 AM

I am very intrigued that you believe the script to be cuneiform. I actually purchased this piece along with a few cylinder seals which were of Babylonian origin. Do you know what the inscription says or what it may relate to? I am familiar with cuneiform tablets and the writing on those looks quite different from the writing on my piece. Could my item contain a more simplistic style of script?

Timo Nieminen · 4th January 2015, 10:08 PM

It's cuneiform, for sure, modified to be cut into the stone with a long cut, and a short cut for the fat end of the wedge. I haven't seen known for sure to be authentic cuneiform inscriptions on stone done like this; the classic examples I've seen use proper wedges cut into the stone.

If one wanted to approximate cuneiform on a stone, using a rotating cutting wheel, this is probably the easiest way.

Trent · 5th January 2015, 01:43 AM

Do you know if there are any ways to test if this is a true ancient piece?

Timo Nieminen · 5th January 2015, 09:52 PM

Microscopic examination of tool marks is good. But then you need to know what you're looking at. But since, as noted above, it looks like it was done using a Dremel or similar, I'd call it almost certainly modern. (IMO, "almost" is generous.)

Shakethetrees · 5th January 2015, 10:24 PM

I believe seal engraving was done by the use of a small wheel driven by a bow in the manner glass engraving is still done today.

The principle of a lathe is as ancient a bit of tech as there is, powered by a bow or a treadle. Oil or water with powdered abreasive are splashed on the wheel and work and a steady hand and good eye are the rest.

It would be hard to tell without super close ups old from new.

Wear and "feel", combined with experience, are the only way to tell, and then you could get into a case of dueling experts!

spiral · 9th January 2015, 11:42 PM

Quote:

Originally Posted by Shakethetrees

I believe seal engraving was done by the use of a small wheel driven by a bow in the manner glass engraving is still done today.

The principle of a lathe is as ancient a bit of tech as there is, powered by a bow or a treadle. Oil or water with powdered abreasive are splashed on the wheel and work and a steady hand and good eye are the rest.

It would be hard to tell without super close ups old from new.

Wear and "feel", combined with experience, are the only way to tell, and then you could get into a case of dueling experts!

Your theory is correct, the difference between craftsman & idiots operating a dremel is clear to see to anyone with experience of genuine pieces though.

Thread Tools	Search this Thread
Show Printable Version Email this Page	Search this Thread: Advanced Search
Display Modes
Switch to Linear Mode Hybrid Mode Switch to Threaded Mode

3rd January 2015, 10:53 PM	#1
Vendric Member Join Date: Apr 2011 Location: Lincolnshire, UK Posts: 4	The inscription is in cunieform, but this type of writing was used for a number of languages. I see no reason to doubt the antiquity of the item, but admit that my eyesight is not what it once was.

4th January 2015, 02:41 AM	#2
Trent Member Join Date: Oct 2014 Posts: 8	I am very intrigued that you believe the script to be cuneiform. I actually purchased this piece along with a few cylinder seals which were of Babylonian origin. Do you know what the inscription says or what it may relate to? I am familiar with cuneiform tablets and the writing on those looks quite different from the writing on my piece. Could my item contain a more simplistic style of script?

4th January 2015, 10:08 PM	#3
Timo Nieminen Member Join Date: Mar 2012 Posts: 422	It's cuneiform, for sure, modified to be cut into the stone with a long cut, and a short cut for the fat end of the wedge. I haven't seen known for sure to be authentic cuneiform inscriptions on stone done like this; the classic examples I've seen use proper wedges cut into the stone. If one wanted to approximate cuneiform on a stone, using a rotating cutting wheel, this is probably the easiest way.

5th January 2015, 01:43 AM	#4
Trent Member Join Date: Oct 2014 Posts: 8	Do you know if there are any ways to test if this is a true ancient piece?

5th January 2015, 09:52 PM	#5
Timo Nieminen Member Join Date: Mar 2012 Posts: 422	Microscopic examination of tool marks is good. But then you need to know what you're looking at. But since, as noted above, it looks like it was done using a Dremel or similar, I'd call it almost certainly modern. (IMO, "almost" is generous.)

5th January 2015, 10:24 PM	#6
Shakethetrees Member Join Date: Apr 2014 Location: Louisiana Posts: 363	I believe seal engraving was done by the use of a small wheel driven by a bow in the manner glass engraving is still done today. The principle of a lathe is as ancient a bit of tech as there is, powered by a bow or a treadle. Oil or water with powdered abreasive are splashed on the wheel and work and a steady hand and good eye are the rest. It would be hard to tell without super close ups old from new. Wear and "feel", combined with experience, are the only way to tell, and then you could get into a case of dueling experts!